How to Clean Diamond Earrings, Rings and Bracelets

Warm water, a drop of dish soap and a soft toothbrush cleans any diamond piece. What changes by item is where the dirt collects and what you can damage getting at it: behind the setting on earrings, under the stone on a ring, in every link and the clasp on a tennis bracelet, and all the way around on an eternity band.

Our general method is in cleaning lab grown diamond jewelry at home. This is the per-item version, because a tennis bracelet and a pair of studs fail in completely different ways.

The method, once

  1. Warm water — comfortable to the hand, not hot. Hot water will not hurt a diamond but it loosens some adhesives used in costume findings.
  2. One drop of plain dish soap. Not toothpaste, which is abrasive and will scratch gold.
  3. Soak four or five minutes.
  4. Work a soft toothbrush over the part listed below for your item.
  5. Rinse under running water, with the plug in the sink.
  6. Dry with a lint-free cloth, not paper towel.

Diamonds are 10 on the Mohs scale and cannot be scratched by any of this. Gold is between 2.5 and 3 and scratches easily, which is why the brush is soft and the toothpaste stays in the bathroom.

Earrings: behind the setting, and the backs

A stud dulls from the back, not the front. Skin oil and soap film build up behind the stone where it meets the lobe, and that film is what kills the sparkle while the visible face still looks clean. Brush the underside of the setting, from behind, with the earring held front-down.

Clean the backs separately. A screw back has threads that trap residue, and residue is what makes a screw back feel gritty and eventually stop turning smoothly. If a back has gone stiff, that is usually dirt rather than damage. Replacement backs are available on their own at $129 for a 14K pair if one is lost or worn.

While the earring is out, turn the back gently to check it is still firm. Fastenings loosen with wear long before stones do, and a loose back is how earrings get lost. Our comparison of screw backs and push backs covers which to use for which weight.

Rings: under the stone, where you cannot see

A ring collects soap and hand cream in the gap between the stone's underside and the top of the band — the one part you never look at. Brush from underneath, through the gap in the setting, not across the top.

Two ring-specific warnings. A full eternity ring has stones all the way around, including against the palm, which is where a ring takes its knocks — check those settings under a light every few months, because the underside stones are the ones that work loose. And if you remove a ring to clean it, put it somewhere closed; more rings are lost to a bathroom windowsill than to a faulty setting.

Tennis bracelets: every link, then the clasp

A tennis bracelet is the hardest piece to clean properly and the most rewarding, because it has the most places for film to sit. Lay it flat and work along the line, brushing the underside of each setting in turn. It is tedious. It is also the difference between a bracelet that reads as diamonds and one that reads as gray stones.

Then the clasp, which matters more than the stones. A box clasp with a safety catch collects residue inside the mechanism, and a clasp that no longer clicks firmly shut is the single most common reason a tennis bracelet is lost. Brush inside the catch, rinse it thoroughly, and test the click a few times once it is dry. If the click is soft rather than positive, stop wearing it and have it looked at — that is a repair, and it falls under the lifetime manufacturing warranty.

Sizing and fit matter here too: a bracelet that spins brings the clasp to the top of the wrist where it catches on things. Our bracelet sizing guide covers the half-inch rule.

Pendants: the bail and the chain

The stone is the easy part. The bail — the loop the chain passes through — wears from the inside as the chain moves against it, and that wear is invisible until it fails. Look at the bail from the side under a light: if the metal has thinned to a visible notch, have it repaired before wearing it again.

Chains hold more skin oil than any other part of a piece. Soak the chain, then run it through a soft cloth between finger and thumb along its length rather than brushing it.

What not to do

Avoid Why
Toothpaste Abrasive. It will not scratch the diamond but it dulls the gold around it.
Bleach or chlorine Attacks the alloys in gold. Take jewelry off before a swimming pool or a hot tub.
Ultrasonic cleaners at home Fine for a plain solid band, risky for anything with many small stones. The vibration can walk a stone loose in a worn setting, and you will not know until it is gone.
Steam cleaners Same reason, plus the thermal shock.
Cleaning over an open drain The most expensive mistake in this article.
Hand cream before earrings It transfers straight onto the setting and is the main source of the film you are cleaning off.

How often

Pieces worn daily — studs, a wedding or eternity band — benefit from this every two to four weeks. Occasion pieces need it before wearing rather than after, because film builds up in storage too. Have settings checked once a year on anything with many small stones: halo earrings, tennis bracelets and full eternity bands all have more prongs than a solitaire and more places to work loose.

Store pieces separately so they do not rub. The detail is in our post on storing diamond jewelry.

What is covered if something is wrong

Every Shop QSE piece carries a lifetime manufacturing warranty, which covers faults in how it was made — a setting that was never seated correctly, a clasp that fails in normal use. It does not cover accidental damage or loss. Eligible pieces can be returned within 30 days under our return and exchange policy, with custom and engraved work excluded.

Common questions

How do I clean diamond earrings?

Soak in warm water with one drop of dish soap for four or five minutes, then brush the underside of the setting from behind with a soft toothbrush — that is where the film that dulls a stud collects. Clean the backs separately, since screw threads trap residue.

How do I clean a diamond tennis bracelet?

Lay it flat and brush the underside of each setting along the line, then clean inside the clasp and its safety catch. Test the click once dry: a clasp that no longer shuts firmly is the most common reason a tennis bracelet is lost.

Can I use an ultrasonic cleaner on diamond jewelry?

Not at home on anything with many small stones. The vibration can work a stone loose in a setting that has already worn, and you will not notice until it is missing. A plain solid band is lower risk.

Can I use toothpaste to clean diamonds?

No. Toothpaste is abrasive. It will not scratch the diamond, which is 10 on the Mohs scale, but it will dull the gold setting around it, which is between 2.5 and 3.

How often should diamond jewelry be cleaned?

Every two to four weeks for anything worn daily, and before wearing for occasion pieces, since film builds up in storage. Have the settings checked once a year on halo earrings, tennis bracelets and full eternity bands, which have the most prongs.

Why do my diamonds look dull when they are clean?

Because the film is behind the stone, not on the face you are looking at. Brushing the top of a setting achieves almost nothing; the dirt sits underneath where the stone meets the metal and the skin.

Related reading